Key Parameters Category Parameter Description / Typical Values Enclosure Enclosure Material Cast Aluminum with Epoxy Powder Coat. Ingress Protection IP66/IP67 (NEMA 4, 4X, 6 equivalent) - Dust-tight and protected against powerful water jets and temporary immersion. Hazardous Area Certifications ATEX, IECEx (Ex d IIC T6 Gb / Ex tb IIIC T80°C Db), CSA (Class I, Div 1 & 2, Groups A, B, C, D). Electrical Electrical Connections Modular terminal block for easy wiring. Conduit Entries Multiple ½" NPT conduit entries. Switch Types Standard: 2 to 4 snap-action switches (SPDT). Optional: Magnetic proximity switches (Reed switches), Hall Effect sensors. Electrical Ratings Typical Switch: 10 A, 250/480 VAC. (Specific ratings depend on the switch type selected). Mechanical Shaft Rotation Standard 90° adjustment (configurable for other angles). Operating Temperature Standard: -40°F to +165°F (-40°C to +74°C). Optional high-temperature version available. Mounting Directly mounts to the actuator using a standardized interface (e.g., Fisher V-Ball, V500/V600 actuator mounts). Indication Position Indicator Mechanical Flag Indicator: Color-coded (Red/Green) for local visual position indication. Optional Features • Potentiometer for analog position feedback. • Heater Kit for cold environments to prevent condensation. • Solenoid valves for integrated control.

Key Parameters Category Parameter Description / Typical Values Pressure Ratings Inlet Pressure (P1) Up to 4000 psig (275 bar). Outlet Pressure (P2) Range Varies with size and spring/dome load. Typically from 15 to 1500 psig (1 to 103 bar). Consult sizing tables. Max. Shutoff Pressure Up to the maximum inlet pressure rating. Size & Connections Orifice Size Common sizes: 1/2 inch, 3/4 inch, 1 inch, 1-1/2 inch, 2 inch. End Connections NPT (Standard), Flanged (ANSI Class 150, 300, 600, 900, etc.), or SW (Socket Weld). Flow & Performance Flow Coefficient (Cv) High Cv values, e.g., up to 45 Cv for a 2" orifice. Accuracy & Droop Excellent accuracy with minimal droop due to the pilot-operated design. Materials Body Materials Carbon Steel (Standard), Stainless Steel (316). Trim Materials Stainless Steel, etc. Pilot Options Control Type Spring-Loaded Pilot: Setpoint is adjusted by a spring. Dome-Loaded Pilot: Setpoint is controlled by applying an external air or gas signal to the dome, allowing for remote control. Environment Operating Temperature Standard: -20°F to +150°F (-29°C to +66°C). Extended temperature ranges available with optional elastomers.

Key Parameters Category Parameter Description / Typical Values Input Signal Electrical Input 4-20 mA DC (standard); other ranges available (e.g., 10-50 mA, 1-5 VDC). Output Signal Pneumatic Output 3-15 psig (0.2-1.0 bar); other standard ranges available (e.g., 6-30 psig). Air Supply Supply Pressure 20 psig (1.4 bar) minimum to 100 psig (6.9 bar) maximum. Performance Accuracy Typically within ±0.5% of span. Sensitivity Typically within 0.1% of span. Air Consumption Low steady-state air consumption (e.g., < 0.2 SCFM @ no load). Environmental Enclosure Rating NEMA 4X (IP66) - Weatherproof, watertight, and corrosion-resistant. Operating Temperature -40°F to +180°F (-40°C to +82°C). Hazardous Area Certifications Available with certifications for Non-Incendive (NI) and Explosion-Proof (XP) applications (e.g., Class I, Div 1 & 2, Groups A, B, C, D). Physical Enclosure Material Epoxy-coated aluminum. Mounting Directly to actuator yoke (2-bolt pattern) or panel mount. Options & Features Gauge C483-24: Without output gauge. C484-24: With output pressure gauge. Relay Options Standard High-Capacity Relay. Venting Open Vent (standard) or Closed Vent (for specific applications).

Key Parameters Category Parameter Description / Typical Values Valve Body Size Range Typically 1 inch (DN25) to 12 inches (DN300). End Connections Flanged (ANSI Class 150 & 300; PN16/PN40), Wafer style. Pressure Rating ANSI Class 150 & 300 standard. Temperature Range Standard: -20°F to +400°F (-29°C to +204°C). Extended ranges available with different seat materials. Flow & Trim Flow Characteristic Equal Percentage (inherent, via the V-port). Flow Coefficient (Cv) High Cv values. Specific Cv depends on valve size and V-port angle (e.g., 60°, 75°, 90°). Leakage Class ANSI Class VI (Bubble-tight) with reinforced PTFE seats. ANSI Class IV with metal seats. Actuator Type Spring-Return Piston Actuator (Single-Acting). Action Fail-Closed (Air-to-Open) or Fail-Open (Air-to-Close). Air Supply Pressure Typical max supply: 100 psig (7 bar). Spring Ranges Multiple spring ranges available to provide the required torque for the application. Positioner Model Integrated FIELDVUE DVC6000 Series Digital Valve Controller. Signal 4-20 mA DC with HART® communication. Input Signal Functions Valve positioning, performance diagnostics, configuration, and monitoring. Materials Body Materials Stainless Steel (CF8M/316SS) is standard. Other alloys available. Ball & Shaft Stainless Steel. Seat Reinforced PTFE (RPTFE) standard for Class VI shut-off. Metal seats available.

Key Parameters Category Parameter Description / Typical Values Pressure Ratings Maximum Inlet Pressure (P1) 5 psig (0.34 bar) for standard models. Outlet Pressure (P2) Range Adjustable within a range, typically from 3.5" w.c. to 14" w.c. (0.87 to 3.5 kPa) or other similar low-pressure ranges. Specific models cover different ranges. Outlet Pressure (P2) Rating Maximum 2.0 psig (0.14 bar). Capacity Flow Coefficient (Cv) Low Cv, suitable for small lines and low flow rates. Example: Cv ~0.3. Maximum Flow (Natural Gas) Typically around 200 CFH (Cubic Feet per Hour) for natural gas, depending on inlet/outlet conditions. Connections & Size Pipe Size Typically 1/2 inch NPT inlet and outlet. End Connections Female NPT (National Pipe Taper). Materials Body Material Aluminum or Zinc Alloy. Internal Components Stainless Steel, Rubber Diaphragm. Environment Operating Temperature Standard for indoor/outdoor conditions (e.g., -20°F to 150°F / -29°C to 66°C). Applicable Fluids Natural Gas, Air, and other non-corrosive, clean gases.

Key Parameters Category Parameter Description / Typical Values Valve Body & Size Valve Body Style Double-port, top-and-bottom guided, balanced globe valve. Size Range 1 inch (DN25) to 12 inches (DN300). End Connections Flanged (ANSI Class 150 to 2500; PN ratings), Screwed (NPT), Butt-weld. Face-to-Face Complies with ISA S75.08 / IEC 60534-3-1 standards. Pressure & Temperature Pressure Rating Available in a wide range, from ANSI Class 150 to Class 2500. Temperature Range Standard: -20°F to +450°F (-29°C to +232°C). Extended ranges available with special materials and designs (e.g., -450°F to 1100°F / -268°C to 593°C). Flow Characteristics Flow Characteristics Linear, Equal Percentage (via characterized plugs). Flow Coefficient (Cv) A wide range of Cv values available based on trim size and port diameter. Leakage Class Leakage Class ANSI/FCI 70-2 Class II (Standard for double-port design). Class IV or better is achievable with special lapping or single-seat configurations. Materials Body & Bonnet Carbon Steel (Standard), Stainless Steel, Alloy Steel, Chrome-Moly and other alloys. Trim Standard Trim: 17-4PH Stainless Steel. Hardened Trim: Stellite, 440C Stainless Steel for erosive/cavitating services. Actuator Actuator Type Typically paired with Fisher 657/667 Diaphragm Actuators or piston actuators for high-thrust requirements.

Key Parameters Category Parameter Description / Typical Values Power & Performance Operating Principle Rotating eccentric weight generating directional centrifugal force. Centrifugal Force Variable, depending on model and air pressure. Can range from several hundred to thousands of pounds of force (e.g., up to 10,000 lbs or more). Frequency (RPM) Typically in the range of 2,000 to 12,000 VPM (Vibrations per Minute). Adjustable via air pressure. Air Supply Air Pressure Standard operating range: 40 to 100 psig (2.8 to 6.9 bar). Air Consumption Varies significantly with size and speed. Can range from 5 SCFM to over 50 SCFM. Physical Housing Material Cast Iron or Aluminum. Mounting Multiple bolted foot mounts or basepad for secure attachment to the vessel. Weight Varies by model, typically from 10 lbs (4.5 kg) to over 100 lbs (45 kg). Environment Operating Temperature Standard range for ambient industrial conditions. Noise Level Can be significant; optional mufflers are often available to reduce noise.

Key Parameters Category Parameter Description / Typical Values Input Signal Electrical Input 4-20 mA DC (standard; other ranges available). Output Signal Pneumatic Output 3-15 psig (0.2-1.0 bar); other standard ranges available (e.g., 6-30 psig). Air Supply Supply Pressure 20 psig (1.4 bar) minimum to 100 psig (6.9 bar) maximum. Performance Accuracy Typically within ±0.5% of span. Sensitivity Typically within 0.1% of span. Air Consumption Low steady-state consumption (e.g., < 0.2 SCFM @ no load). Environmental Enclosure Rating NEMA 4X (IP66) - Weatherproof, watertight, and corrosion-resistant. Operating Temperature -40°F to +180°F (-40°C to +82°C). Hazardous Area Certifications Explosion-Proof (XP) and Non-Incendive (NI) for Class I, Division 1 & 2, Groups A, B, C, D. Physical Enclosure Material Epoxy-coated aluminum. Mounting Directly to actuator yoke (2-bolt pattern) or panel mount. Options & Features Venting Open Vent (standard) or Closed Vent (for specific applications where venting to atmosphere is not permitted). Gauge Ports Typically includes ports for installing supply and output pressure gauges.

Key Parameters Category Parameter Description / Typical Values Power & Performance Operating Principle High-speed rotary ball within a sealed raceway. Force Output Variable based on air pressure. The "C407-10" model typically generates a centrifugal force of 10 lbs (44 N). Frequency (RPM) High frequency, typically in the range of 12,000 to 16,000 VPM (Vibrations per Minute). Air Supply Air Pressure Standard operating range: 40 to 100 psig (2.8 to 6.9 bar). Air Consumption Varies with pressure; approximately 5 SCFM at 80 PSIG. Physical Housing Material Cast Iron or Ductile Iron. Mounting Standard 1-1/4" - 7 UNC threaded base for easy installation. Weight Approximately 2.5 lbs (1.1 kg). Environment Operating Temperature Standard for ambient industrial conditions. Noise Level Relatively low compared to piston vibrators; typically < 85 dBA.

Key Parameters (English) The following are typical technical parameters for the Fisher N562 Gas Regulator. Category Parameter Description / Typical Values Pressure Ratings Maximum Inlet Pressure (P1) Up to 400 psig (28 bar) for standard models. Outlet Pressure (P2) Range Adjustable within a specific range, commonly from 4" w.c. to 60 psig (1 kPa to 4.1 bar). Specific pilots determine the exact range. Capacity Flow Coefficient (Cv) High Cv values. For example, a 2" N562 can have a Cv of approximately 65. Accuracy Excellent accuracy with minimal droop, typically within ±5-10% of the set point. Size & Connections Pipe Size Typically 1/2 inch to 4 inches. End Connections Flanged (ANSI Class 125/150) or Threaded (NPT). Materials Body Material Cast Iron (standard), Ductile Iron, or Aluminum. Internal Trim Stainless Steel, Brass. Safety Features Internal Relief Options Monitor Relief Regulator, Slam-Shut Device, or Spring-Loaded Relief Valve. Environment Operating Temperature Standard for outdoor gas service (e.g., -20°F to 150°F / -29°C to 66°C).