Technical Parameters Category Parameter Specification / Description General Model DVC6030AC Type Digital Valve Controller (AC Powered) Product Family FIELDVUE Primary Protocol HART Input & Power Input Signal 4 to 20 mA DC (for control and HART communication) Power Supply 120 VAC, 50/60 Hz (Standard) Power Consumption 12 VA (typical) Performance Output Capacity Standard pneumatic relay. Suitable for most standard and high-volume actuators. Linearity ±0.5% of span Hysteresis Less than 0.4% of span Air Consumption Steady State: ~0.04 SCFM (1.1 NLPM) Environmental Ambient Temperature -40°F to 185°F (-40°C to 85°C) Enclosure Rating Type 4X, 6 (IP66/67); Dust-tight and protected against water. Hazardous Area Certifications FM/CSA: Explosion-proof (Class I, Div. 1 & 2, Groups A,B,C,D; Class II & III). ATEX/IECEx: Ex d (Flameproof) Physical Conduit Openings Multiple for power, signal, and accessory conduits. Pneumatic Connections Supply & Output: 1/4" NPT

Technical Parameters Category Parameter Specification / Description General Model L2 Type Ball Float Level Controller Mechanical Float Material Copper (Standard for water), Stainless Steel, or other materials for corrosive liquids. Lever Arm Length Standard lengths available to suit various tank depths. Mounting Typically mounts on the side or top of a tank. Performance Level Control Range Adjustable within the limits of the lever arm length. Differential The difference between pump start and stop levels is adjustable. Electrical (if applicable) Switch Rating For electric models: Common ratings are 1/2 HP to 3 HP at 120/240/480 VAC. Enclosure Weatherproof (NEMA 4) or Explosion-Proof (NEMA 7) enclosures available. Pneumatic (if applicable) Supply Pressure Typically 20-100 psig (1.4-6.9 bar). Pilot Valve Output On/Off air signal to operate a pneumatic pump motor starter or other device. Environment Liquid Specific Gravity Typically designed for S.G. > 0.7. Temperature Limits Standard materials suitable for most water and wastewater temperatures.

Technical Parameters Category Parameter Specification / Description General Model 667-30i Type Pilot-Operated, Indicating Actuator Pressure Regulator Input & Output Input Signal 3 to 15 psi (0.2 to 1.0 bar) Supply Pressure Up to 150 psig (10.3 bar) Output Pressure 0 to Supply Pressure Performance Accuracy ±1% of span (including linearity, hysteresis, and repeatability) Air Consumption Steady State: ~0.15 SCFM (4.2 NLPM) During Stroking: ~2.0 SCFM (56.6 NLPM) Capacity (Cv) Approximately 0.7, providing high flow for fast actuator response. Environmental Ambient Temperature -40°F to 180°F (-40°C to 82°C) Enclosure Rating Type 3, 3R, 4, 4X, 12 (NEMA); Weatherproof and corrosion-resistant. Material Aluminum with corrosion-resistant coating. Physical Pressure Gauge Included (1.5" dial, 0-150 psi range) - this is the "indicating" feature. Pipe Connections 1/4" NPT for Supply, Input, and Output ports. Weight Approximately 5 lbs (2.3 kg)

Technical Parameters Category Parameter Specification / Description General Part Number 24490-1 Description Trim Kit (Cage, Plug, Seat Ring) Components Included Parts Cage, Control Plug, Seat Ring. Typical Specifications Valve Size This specific kit is commonly used for 1.5 inch (NPS 1-1/2") ET valves. This must be verified. Pressure Class Likely for ANSI Class 150 or 300 valve bodies. Flow Characteristic Defined by the cage port design (e.g., Equal Percentage, Linear, Quick Opening). The exact characteristic is part of the -1 suffix designation. Trim Level Likely Standard Trim. This kit may also represent a specific "soft" seat version for tight shut-off. Materials Cage & Plug Material Typically Stainless Steel (e.g., 316 SS). Seat Material Could be metal (Stainless Steel) or a soft seat (e.g., PTFE) for enhanced shut-off (Class VI).

Fisher 24000-333 is a high-performance control valve trim assembly designed for Baumann 24000 series control valves. Manufactured with premium 316 stainless steel, it delivers excellent corrosion resistance and reliable operation. Engineered for precise flow regulation in liquid, gas and steam applications, it ensures stable performance, tight shutoff and long service life in industrial processing systems.

Technical Parameters Category Parameter Specification / Description General Model 627-348 Type Pilot-Operated Backpressure/Relief Regulator Pressure & Capacity Body Pressure Rating (ANSI) Typically ANSI Class 300, 600, or higher. Max. Inlet Pressure (P1) Up to 1440 psig (99 bar) or higher, depending on body class. Setpoint Pressure Range Defined by the pilot spring. The "-348" code specifies a particular range, which could be in the hundreds of psig. Flow Capacity (Cv) Very High. Specific Cv depends on main valve size (e.g., 2", 3", 4", 6"). Can range from ~100 to over 1000. Construction & Materials Body Materials Carbon Steel (Standard), Stainless Steel, Other Alloys. Trim Materials Stainless Steel. Pilot Valve 627 Pilot (Relief Pilot) - senses upstream pressure. Connections & Environment Inlet/Outlet Connections Flanged (RF, RTJ) per ANSI standards. Vent Connection Flanged or threaded. Ambient Temperature Standard: -20°F to 150°F (-29°C to 66°C).

Technical Parameters Category Parameter Specification / Description General Model 627-328 Type Pilot-Operated Backpressure/Relief Regulator Pressure & Capacity Body Pressure Rating (ANSI) Typically ANSI Class 300, 600, or higher. Max. Inlet Pressure (P1) Up to 1440 psig (99 bar) or higher, depending on body class. Setpoint Pressure Range Defined by the "-328" suffix. This code specifies a particular pilot spring that corresponds to a specific, narrow pressure range (e.g., 30-120 psig, 200-400 psig, etc.). *This is the primary difference from the 627-348.* Flow Capacity (Cv) Very High. Specific Cv depends on the main valve size defined by "-328". Construction & Materials Body Materials Carbon Steel (Standard), Stainless Steel, Other Alloys. Trim Materials Stainless Steel. Pilot Valve 627 Pilot (Relief Pilot) - senses upstream pressure. Connections & Environment Inlet/Outlet Connections Flanged (RF, RTJ) per ANSI standards. Vent Connection Flanged or threaded. Ambient Temperature Standard: -20°F to 150°F (-29°C to 66°C).

Technical Parameters Category Parameter Specification / Description General Model 98L-48.MR95HT Actuator Type Double-Acting Piston Positioner MR95HT Multi-Spring, High-Thrust Positioner Actuator Performance Piston Diameter The "48" likely indicates a 48 square inch effective piston area. Stroke Length Long stroke, specific length defined by the "L" in 98L (e.g., 8 inches or more). Thrust Output Extremely High. With a 48 in² piston at 100 psig air supply, theoretical thrust is 4,800 lbs. Actual thrust depends on friction and positioner capability. Air Supply Pressure Typically up to 100-150 psig (6.9-10.3 bar) for the actuator. Positioner (MR95HT) Input Signal 3 to 15 psi (0.2 to 1.0 bar) pneumatic Supply Pressure Up to 150 psig (10.3 bar) Output Capacity Very High. Designed to provide large volumes of air to quickly fill and exhaust the large piston chamber. Characterization Linear, Equal Percentage, Quick Open (via characterized cams). Environmental & Physical Ambient Temperature Standard: -20°F to 150°F (-29°C to 66°C) Enclosure Rating Weatherproof and/or Explosion-Proof (depending on ordered configuration). Materials Cast iron or ductile iron construction.

Technical Parameters Category Parameter Specification / Description General Model DVC6015 Type Digital Valve Controller (Single-Action) Product Family FIELDVUE Primary Protocol HART Input & Output Input Signal 4 to 20 mA DC, two-wire Supply Pressure Up to 150 psig (10.3 bar) Output Action Single-Action (One output port for spring-return actuators) Performance Linearity ±0.5% of span Hysteresis Less than 0.4% of span Air Consumption Steady State: ~0.04 SCFM (1.1 NLPM) Environmental Ambient Temperature -40°F to 185°F (-40°C to 85°C) Enclosure Rating Type 4X, 6 (IP66/67); Dust-tight and protected against water. Hazardous Area Certifications FM/CSA: Explosion-proof, Intrinsically Safe (Class I, II, III, Div. 1 & 2) ATEX/IECEx: Ex db, Ex tb, Ex ia [ia] (Zone 1 & 21) Physical Conduit Openings Two 1/2" NPT Pneumatic Connections Supply & Output: 1/4" NPT

Technical Parameters Category Parameter Specification / Description General Model DVC6200PD Type Digital Valve Controller (Point-to-Point Digital) Product Family FIELDVUE Primary Protocol Foundation Fieldbus H1 or PROFIBUS PA (specified when ordered) Input & Power Signal & Power Digital signal and device power are provided on the same two-wire loop. Supply Voltage Typically 9-32 V DC (for Foundation Fieldbus) Communication Speed 31.25 kbit/s (Foundation Fieldbus H1) Performance Linearity ±0.5% of span Hysteresis Less than 0.3% of span Air Consumption Steady State: ~0.04 SCFM (1.1 NLPM) Output Capacity Standard and High-Capacity (HC) output modules available. Environmental Ambient Temperature -40°F to 185°F (-40°C to 85°C) Enclosure Rating Type 4X, 6 (IP66/67); Dust-tight and protected against water. Hazardous Area Certifications FM/CSA & ATEX/IECEx: Intrinsically Safe, Flameproof, and Non-incendive approvals for use in hazardous areas. Physical Conduit Openings Two 1/2" NPT Pneumatic Connections Supply & Output: 1/4" NPT